COSMOING DOORBELL QUITE START GUIDE
DOORBELL INSTALLATION
Tip: The recommended installation height is 1.2 meters from the ground
1. Before mounting, test the doorbell range. Press the doorbell button to verify that the doorbell work properly. Use a small flat blade screwdriver to remove the Push Botton cover.
2. Drill two holes on the marked locations,then screw the wall plate to the wall or use double-sided tape to mount the Push Botton.
l Package Contents
1 x Push Botton
1 x Doorbell
2 x Screws & Wall anchors
1 x Double-Side Tape
1 x Quick Start Guide
l Technical Specifications:
1. Push Botton uses Battery CR2032.
2. Doorbell is with LED.
3. Doorbell offers 32 different ringtones.
4. Doorbell with volume control.
5. 180M operating range in the open air.
6. Power requirements 110V~220V/50Hz Input, with US plug.
l Installation:
Features of technolygy:
The Push Botton can be mounted on door frame.
The Doorbell chime should be plug-in the socket for main power supply.
l How to Pairing:
The bell Push Button and Doorbell have been pairing during the packaging. If your Doorbell is not working well. You can follow up below 3 steps to reset the product.
1. Clear the pairing codes inside of the Doorbell. Firstly, press and hold the "Music Switch button", and plug it into the socket until you see the Doorbell's LED flashing and hear the sound, then release the button, reset is completed.
2. Pairing the bell Push Button and Doorbell. Press and hold the "Music Switch button" until you hear "Ding-Ding" sound, press the bell Push Button and you will hear the Doorbell play "Ding" sound, press the "Music Switch button" to exit the paring mode, now you can start using the Doorbell.
3. Change melody: press the "Music Switch button" to select your desired melody.
l Troubleshooting
Chime does not sound:
•Make sure the doorbell button and the chime codes are the same.
•Check orientation of doorbell button battery.
Batteries seem OK, but the chime does not work when installed:
•Do not mount the chime or doorbell button on metal or near metal studs.This reduces the transmitter range. Use 1/4" to 1/2" (6 to 13 mm) wood shims to move the chime or doorbell button off the metal surface.
•Do not mount the chime too close to ground level concrete slabs. This may also reduce the range. Mount the chime away from the floor.
•Try different locations for the chime closer to the doorbell button. Also try to orient the chime at a different angle to increase the range. The range of the doorbell depends on location, temperature and battery con-dition.
l FCC WARNING
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help.
l WARRANTY INFORMATION
This product is guaranteed for one year from date of purchase(Batteries are not covered).
Contact the Customer Service Team at
Email: ad@cosmoing.cn
or visit www.cosmoing.cn